- Listeria monocytogenes can persist in food manufacturing environments, often within specific equipment or structural niches.
- The first table lists areas and equipment components known to harbour L. monocytogenes and details corrective measures that effectively removed contamination.
- The second table provides an example environmental sampling programme to help identify contamination in fish processing plants.
Decontamination approaches reported in published literature
In summary:
Selection of environmental sampling sites likely to harbour L. monocytogenes
The table below presents a list of niches that L. monocytogenes was isolated from in various food processing facilities, along with corrective actions that successfully removed contamination. The list should not be considered an exhaustive list of niches that may become contaminated. Is adapted from Tompkin and is intended to help plant operators identify likely contamination sites and apply proven decontamination strategies for both equipment and processing environments1.
| Contaminated equipment | Contamination source | Successful corrective actions taken |
|---|---|---|
| Continuous brine chill chamber for product on racks with wheels | Doors made of rubber-coated fabric, large metal hinges extending the width of the door, and hollow bump guards at bottom of door | Doors replaced with rigid, cleanable plastic material; large hinges and bump guards removed |
| Ammonia unit used to chill brine solution | Fibreglass insulation on ammonia line became saturated with brine splashing from chilling unit | Contaminated insulation removed; pipe and surrounding area cleaned and sanitised; insulation not replaced near the chiller |
| Brine chill exit | Hoses and spray nozzles used to spray product | Hoses and nozzles replaced; daily cleaning and sanitisation initiated |
| Brine chill | Stainless steel framing with metal-to-metal contact creating uncleanable hollow space | Framing modified to allow cleaning and prevent debris accumulation |
| Brine chill tunnel | Damaged rubber seals on stainless steel door | Seals replaced; cleaning procedures tightened |
| Conveyor belt | Contaminated liquid found inside hollow sprocket that had split open | Hollow sprocket replaced with solid version |
| Conveyors (multiple events) | Hollow rollers | Rollers replaced when contamination detected; where possible, conveyors replaced with sloping steel chutes to eliminate rollers |
| Conveyor between shrink tunnel and boxing | Worn rubber-coated fabric belt | New belt fitted |
| Collator and conveyor | Undetermined | Equipment covered with tarpaulin and steam injected underneath |
| Exit from spiral freezer / Spiral freezer | (1) Wheel bearings for conveyor belt (2) Undetermined | (1) Bearings replaced (2) Cleaning frequency increased; equipment defrosted properly before cleaning |
| Between freezer and packing machine / Wire mesh conveyor between oven and freezer | (1) Overhead conveyor (2) Hollow support rods | Hollow rods replaced with solid rods |
| Slicer | Worn hydraulic seals at base, oil mixed with water and product residue | Slicer stripped, cleaned, and sanitised; components heat-treated; sodium benzoate oil used for lubrication |
| Slicer | Product residue build-up inside safety cover contaminating conveyor below | Cover redesigned for nightly removal and cleaning |
| Dicer (multiple events) | Undetermined | Entire dicer heat-treated in oven and steam-cleaned under tarp |
| Conveyor leading to packaging machine / Cooked product worktable | (1) Fabric conveyor material (2) Handheld knives | (1) Conveyor replaced with stainless steel chute (2) Knives cleaned daily in automatic washer and stored hygienically |
| Work table | Air duct blowing product storage bags open | Duct modified for nightly cleaning access |
| Packaging machine | Crack in stainless steel cover near product loading area | Area cleaned, sanitised, and welded shut |
| Packaging machine | Steel rods for pushing product into cartons | Rods removed and cleaned daily |
| Insulated concrete block wall | Condensate contamination between fibreglass and concrete wall | Fibreglass removed; wall acid-cleaned, sanitised, and sealed; pipes rerouted closer to floor |
| Ingredients’ hoppers | Cinder blocks around wall opening | Blocks sealed to prevent moisture accumulation |
| Refrigeration unit near ceiling | Condensate from refrigeration unit | Unit cleaned and sanitised |
References:
- Tomkin, R. B. (2002). Control of L. monocytogenes in the food-processing environment. J. Food Prot. 65, 709-725
- Simmons, C.K. and Wiedmann, M. (2018) Identification and classification of sampling sites for pathogen environmental monitoring programs for Listeria monocytogenes: Results from an expert elicitation. Food Microbiol. 75, 2-17.